Sika AnchorFix Grey Adhesive – 1 0.3L

Sika AnchorFix – 1 is a two-component anchoring adhesive based on styrene-free polyester resin and solvents.

• Fast drying.
• Applicable with conventional spray guns.
• It can be used at low temperatures.

Colour :

• Component A: White
• Component B: Black
• Mixed A+B components : Light grey

 

• Shelf life: 12 months from date of manufacture.The expiry date is printed on the label of all Sika AnchorFix – 1
• Storage conditions: In their original, tightly closed and undamaged containers, stored in a cool, dry place at temperatures between +5ºC and +25ºC. Protected from direct sunlight.
• Density: 1.63 kg/l (components A+B mixed).

Sika AnchorFix Technical Information – 1

• Compressive strength: ~ 60 N/mm2 (7 days, +20°C) (ASTM D 695)
• Modulus of elasticity in compression:~ 3,500 N/mm2 (7 days, +20°C) (ASTM D 695)
• Flexural strength: ~ 28 N/mm2 (7 days, +20°C) (ASTM D 790)
• Shear strength: ~ 12 N/mm2 (7 days, +20°C) (ASTM D 638)
• Thermal resistance:

+50ºC prolonged exposure
+80ºC short exposure (1-2 hours)

• Glass transition temperature(GT): +60°C(DIN EN ISO 6721-2)
• Operating temperature :

Long-term -40 °C min. / +50 °C max.
Short term (1-2 hours) +80 °C

Application Information

• Mixing ratio:Component A : Component B = 10:1 by volume.
• Layer thickness:Maximum 3 mm
• Thixotropy: No sagging, also applicable to ceilings.
• Product temperature: Min. -10°C/ max. +40°C.
  Sika Anchorfix – 1 must be kept at a temperature between +5°C and +40°C during application.
• Ambient temperature : Min. -10°C/ max. +40°C. Sika Anchorfix®1 must be kept at a temperature between +5°C and +40°C during application.
• Dew point: Beware of condensation.
  The substrate temperature during application must be at least 3°C above the dew point.
• Mediatemperature : -10 °C min. / +40 °C max.
• Maximum time after opening :

Application temperature	Open time
–10 °C* **	30 minutes
+5 °C	18 minutes
+5 °C – +10°C	10 minutes
+10 °C – +20 °C	6 minutes
+20 °C – +25 °C	5 minutes
+25 °C – +30 °C	4 minutes
+30 °C	4 minutes

* The minimum temperature of the cartridge must be +5°C.

** This application is not covered by the scope of the ETA or other regulations.

• Drying time :

Application temperature	Drying time
–10 °C* **	24 hours
+5 °C	145 minutes
+5 °C – +10°C	145 minutes
+10 °C – +20 °C	85 minutes
+20 °C – +25 °C	50 minutes
+25 °C – +30 °C	40 minutes
+30 °C	35 minutes

* The minimum temperature of the cartridge must be +5°C.

** This application is not covered by the scope of the ETA or other regulations.

Preparation of the Support

• Concrete and mortar substrates must have a minimum strength. They do not have to be 28 days old.
• The strength of the substrate (concrete, masonry, natural stone) must be checked.
• Pull-out tests should be carried out if the strength of the substrate is unknown.
• The surface of the borehole must be clean, dry, free of grease and oil, etc.
• Poorly adhering particles should be removed from the drill holes.
• Corrugated steel rounds and threaded rods must be cleaned of oil, grease or other substances or particles such as dirt, etc.

Mixture

• Take the cartridge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When work is interrupted, the mixing nozzle may remain in the cartridge. If the resin has hardened in the nozzle when work is resumed, a new nozzle must be used.

Tool cleaning

Clean tools and application equipment with Sika Colma Cleaner immediately after use. Once cured, the product can only be removed by mechanical means.